103/05 P/N 211014Toll-Free Customer Service Number for U.S: 1-800-558-5234,For Canada: 1-800-284-8339,For Europe: 00 800 555 85234 (Sweden: 009 555 8
10P/N 211014 03/05SECTION A: ASSEMBLE THE POLES Wood ScrapP-2P-15"(13 cm)5"(13 cm)P-1P-3P-2Pole IdentificationStickerPole IdentificationStic
1103/05 P/N 211014While maintaining alignment, bounce assembly and lower section (P-3) together as shown until they nolonger move toward taped referen
12P/N 211014 03/05SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’vefinished this section.1.Insert axle (P-5) through wh
1303/05 P/N 2110143.Install rod (H-5) through holes in bottom pole section (P-3) and eyebolt (H-6).2.Install wheel assembly to base (P-8) using bolt (
14P/N 211014 03/05H-26H-5H-6P-8H-4P-26TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULTIN SERIOUS INJURY AND/ORPROPERTY
1503/05 P/N 2110145.P-13P-13Secure tank struts (P-13) to pole using bolt (H-3), washers (H-4) and nut (H-23) as shown. Placebolt cover (H-7) over exp
16P/N 211014 03/056.7.Secure ends of tank struts (P-13) to tank usingbolt (H-21), washers (H-4) and nut (H-11) asshown. Repeat for opposite side.Insta
1703/05 P/N 211014H-1P-6P-5P-4P-6H-110.SIDE OF WHEEL WITHLONGER PLASTICAXLE NEEDS TO FACETHE WHEEL BRACKET.IMPORTANT!Insert axle (P-5) through wheel b
18P/N 211014 03/05Position base as shown. Secure wheel bracket assembly with disc (P-23),washer (H-9) and nut (H-26) as shown.H-10P-23H-9H-26Carefully
1903/05 P/N 211014SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOARDThis is what your system will look like when you’vefinished this section.Sec
2P/N 211014 03/05 201246 11/04In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND
20P/N 211014 03/05P-1P-18P-20H-15H-15P-19H-17P-20P-19P-17H-18H-19H-181.While the system is securely resting on the sawhorse.Install triangle plates (P
2103/05 P/N 2110142.3.Remove packaging materials from handle assemblies (P-10 and P-11).Remove screws on both sides of tube.P-11P-10P-11Slide upper tu
22P/N 211014 03/05Insert spacer (H-22) through springs (P-12)then assemble lower elevator tubes (P-19),and springs (P-12), to brackets (P-21) usingbol
2303/05 P/N 2110147.P-31H-33H-32P-30H-31Install Slam Jam Rim to BackboardP-29P-32H-31H-32H-33ABCDEA. Fit rim (P-29) securely into bracket (P-30) as sh
24P/N 211014 03/05P-20P-20H-18H-20P-21H-15H-20Assemble upper elevator tubes (P-20) to brackets using bolt (H-18), plastic spacers (H-20), and nut(H-15
2503/05 P/N 211014H-18H-15P-1P-20P-19P-17P-119.Install handle assembly (P-10 and P-11) to lower elevator tubes (P-19) using bolt (H-18), spacers (H-14
26P/N 211014 03/05P-20P-12H-15P-2011.Insert bolt (H-18) through left side upper elevator tube (P-20),then stretch spring (P-12) onto bolt (H-18). Con
2703/05 P/N 21101412.Install net clips (H-28).CLIP “ARM”CLIP “BODY”Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly sothat se
28P/N 211014 03/05Insert net into bottom of clip as shown.SIDE VIEWTwist net until it snaps into position.Net must be centered through clip. NETNET CL
2903/05 P/N 211014SECTION D: INSTALL FRONT COVER & HANDLE1.Attach front cover (P-22) to hinge tubes (P-16) using carriage bolts (H-27) and flange
303/05 P/N 211014IMPORTANT!Remove all contents from boxes.Be sure to check inside pole sections;hardware and additional parts are packed inside.NOTICE
30P/N 211014 03/051.Roll assembly to desiredplaying area. Secure assemblyto ground using strap (P-26)and tie down stake (P-25). P-26P-25P-8SECTION E:
4P/N 211014 03/05Get to know the basic parts of your basketball system...FRONT VIEWTOP POLEBACK VIEWMIDDLEPOLEFRONTCOVERRIMBOTTOMPOLESTRUTSELEVATORASS
503/05 P/N 211014PARTS LIST (SEE PARTS IDENTIFIER)Item Qty Part No DescriptionP-1 1 908164 Top Pole SectionP-2 1 908107 Middle Pole Section (with Labe
6P/N 211014 03/05PARTS IDENTIFIERP-31 (1)P-30 (1)P-18 (1)P-26 (1)P-28 (2)P-32 (1)P-22 (1)P-23 (1)P-29 (1)P-24 (1)P-25 (1)P-21 (2)P-19 (2)P-20 (2)P-14
703/05 P/N 211014HARDWARE LIST (SEE HARDWARE IDENTIFIER)Item Qty Part No DescriptionH-1 4 206938 Pushnut, BlackH-2 1 203223 Bolt, Carriage, 5/16-18 x
8P/N 211014 03/05Item H-6 (1)Item H-8 (1)Item H-12 (1)Item H-18 (8)Item H-19 (1)Item H-31 (1)Item H-25 (2)Item H-21 (2)Item #H-29 (4)Item H-3 (1)Item
903/05 P/N 211014Item H-20 (4)Item H-23 (2)Item H-26 (6)Item H-4 (7)Item H-15 (8)HARDWARE IDENTIFIER (NUTS, WASHERS & METAL SPACERS)HARDWARE IDENT
Commentaires sur ces manuels